Hello JohnI bought a replacement Top Slide for my Raglan 5" from lathes.co.uk but it turned out to be the wrong size.I crashed my original and am trying to find a replacement.If I took some pictures of the original and the replacement supplied along with some measurements, do you think there would be anything you could do to help - perhaps make a replacement, and how much do you think it would cost ?CheersPaul
Hi PaulDo you still have the first top slide that you bought that turned out to be the wrong size? I am trying to get one for a Little John Mk 2 lathe.TaAlan
HiyaHow much do you sell the little john t-slot top slide for?
HiI've be very interested in buying a 160mm backplate for my Raglan from you.Could you drop me an email or let me know how to contact youCheers
Hi,Ditto above. Please drop me an email with your contact and pricing info.I'm in USA.Thanks,
Hi, I an desperate for a Raglan little john threaded chuck back plate or a three jaw self centering 5" chuck ready mounted on the Raglan backing plate.Can contact me at: email@example.com
Hi any chance of getting a little john rack gear? if so please could you contact me by email to firstname.lastname@example.org Thanks Richard
Are you still making parts for the Little John 5" cross slides?
Hi,I am after one of your cross slides with the T slots for a Raglan Mk 2 lathe, are they still available?
Hi , I have a little John lathe , and need some change gears for cutting DP worms. Is there any available now , or is there any information about the number of teeth in these gears and the set up to use?? Any help would be very gratefuly received.My email is 217.jims.workshop @gmail.comThanks a lot, Jim Simpson
Do you still have backplates for Raglan 5"?Thankjssimon.email@example.com
Hi JW,Would you have a top slide nut for a Raglan 5" available?1/2" ACME RH thread. Postage to Auckland, NZ.Cheers, Brian.
Hi im in New Zealand im after the Little John Rack gear . You list it for £20 . How can i buy this from you Stevekeenboyd@yahoo.com.au
Hi JW, Is the back gear assembly shown suitable for a little john mark one lathe?Im assuming the tooth counts are 21 and 62 and the internal bore is around 28.4mm? If this is still available may I please ask how much it would cost including shipping within England.CheersKind regardsJack
On the front page you are advertising a Raglan Rack Gear for £22.00. Is there one still available?I require one for my Littlejohn Mk 2 Lathe.
At the top of the page you are advertising a rack gear @ £20. Is this still available please?
Do you have a rack gear for a little john mk1
Hi, I am looking for a tee slotted cross slide and screw for my Raglan 5 inch ( not little John ). Be very keen to buy if you have one
Hi John I'm looking for a carriage screw bush and tail stock bush for a Little John mk3. I recently emailed you.Thanks Mike
Hi John, will you supply a little john rack gear please?Thanks, Ed
Hi m8 I'm after a little john cross slide nut
i, i have just broke the drive belt on my raglan variable speed and need a replacement urgently, can you help with this please
Hi I am desperate for a forward reverse tumbler lever and posibly two gearshafts.or any info thanks firstname.lastname@example.org
Hi there Iam after a x axis nut for a raglan mill.I understand it’s the same as the littlejohn nut 16 x 1Can you help?RegardsChris
Hi I'm trying to get a replacement bronze nut for my Raglan cross slideit's 8TPI left hand square section
Hello Are you still making cross and topslide screws and nuts for Mk2 AUD boxfords? ThanksAndy
Hi, does anyone know where I can get a cross slide nut for the later Raglan 5 inch.Thank youRichard
Good morning John, I have a Raglan 5" and looking for -Cross slide nut (5/8" 8tpi) and Compound nut (1/2" x 10) Tumble gears(fibre) 2 off (2"OD 26t)Steel gear that the tumble gears mesh with.Thanks for you helpRegards Paulpaul@minimotorsportcentre.com
My Testimony Hello everyone. Am here to testify how I got my loan from Mr. Benjamin after I applied several times from various loan lenders who promised to help but they never gave me the loan. Until a friend of mine introduced me to Mr.Benjamin Lee promised to help me and indeed he did as he promised without any form of delay.I never thought there are still reliable loan lenders until I met Mr. Benjamin Lee, who indeed helped with the loan and changed my belief. I don't know if you are in any way in need of a genuine and urgent loan, Be free to contact Mr. Benjamin via WhatsApp +1-989-394-3740 and his email: email@example.com thank you.
needing raglan 5 cross slide nut
hi there . Do you still have any little john mk2 backplates?many firstname.lastname@example.org
I just bought a Raglan 5" lathe. Anyone know where I can buy a full set of change gears plus the 52T & 48T bottom tumblers for cutting metric threads.Thanks
Hi there, I am looking for two change wheels for a Little John Mk2, 30 tooth and 60 tooth. Thanks
hi, i am looking for a pinion rack gear for my 5" raglan. hope someonecan help....thanks john.....